Step Plumbing Guide for Installing a Bathtub

Phone

The author is making a number of good annotation relating to How to Install a Bathtub overall in this great article which follows.


Installing A Bathtub
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is likewise a reasonably hard task. If the old bathtub is easily obtainable, the project can move easily; if you need to open up a wall surface to remove the old tub as well as position the brand-new tub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old tub and set in the brand-new one. See to it you have actually certified yourself for the work as well as fit attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly help you install a new bathtub in your restroom if you have currently acquired a brand-new bathtub and do not require to alter the plan of your previous water system pipelines.
Your devices and also material checklist must make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite problematic because of the limited accessibility that is typically the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
    Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
    If you need to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in area between the tap and the sink. Secure the tap in place with the producer provided backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.

    Setting up the Bathtub


    Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wood boards are handy in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
    The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the bathtub up until the level reviews level.
    To mount taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression join; then do the very same for the other tap.
    Turn on the water supply as well as inspect all joints and new pipework for leakages as well as tighten them if necessary. Load the tub as well as additionally examine the overflow outlet and also the normal electrical outlet for leakages.
    Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub must wait till the bathtub has been made use of a minimum of when as this will settle it right into its final setting.

    Planning for the Installment


    To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
    Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to now be ready to be suited its final setting.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to crack an inflexible seal, causing the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
    You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to always load the bathtub with water before sealing, to permit the movement experienced when the tub remains in use. The sealer can split fairly very early if you do not think about this motion before securing.
    Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As a fervent person who reads about Tools You Need to Install a New Bathtub , I thought sharing that excerpt was a good idea. Kindly take the opportunity to distribute this blog if you enjoyed reading it. Thanks a lot for your time invested reading it.


    Ring for results!

    Leave a Reply

    Your email address will not be published. Required fields are marked *